16-12-2020, 03:45 PM
Igor
I have racked up some 4000 FT8 QSOs in the last 2 1/2 years - almost all on HF - and I almost exclusively use the "Hold Tx Freq" box ticked. Recently on 50MHz to work some FT8 6M DX, I think everybody whose signals I saw/worked must have had their box ticked. Everyone in VK and ZL just stayed on 'their' one frequency.
Probably 25-50% of HF users seem to leave theirs unticked as they end up, however briefly, on the called station's frequency. The rest (50-75%) stay on a specific frequency regardless of who they work so their box is obviously ticked. It's not rocket science and once ticked, it stays that way until deliberately unticked.
One thing that does become obvious though is that operators do not use the waterfall display effectively. I often see a 'continuous wall of signals" in some parts of the audio spectrum, usually mid-band, from HF while others are sparsely used. The WSJT-X software does a magnificent job of handling overlapping 50Hz signal 'bands', and even one completely of the top of the other. On the subject of the waterfall, remember that what you see denoting activity is not what the people at the other end see. There are so many signals being emitted in Europe and the Americas on HF that don't make it this far around the globe but it makes it hard for us to find a frequency that isn't in use over there. A deliberate operating ploy is to jump your transmit frequency around a bit if you cannot 'make or complete the contact' in the hope that somewhere along the line you will land on a 'clear frequency' at their end. Same thing happens at VHF.
You mention 'at least 300 to 2500 Hz' but I often see signals down at 200Hz and below, and up at 3KHz and slightly over. What some operators fail to recall is that the likes of a typical USB (or LSB) filter attenuates everything below 300Hz and above 2400-2500Hz, not to mention audio filtering in the interconnecting audio interface. Modern DSP rigs have other bandpass options but not all are using these rigs, just luckily I am and I use it carefully. I don't transmit with a setting below 400 or above 2200 as a matter of course.
It comes down to : if you see what looks like a spare 50Hz over several 30 second segments, grab it - but be prepared to QSY as needed.
73 Doug
I have racked up some 4000 FT8 QSOs in the last 2 1/2 years - almost all on HF - and I almost exclusively use the "Hold Tx Freq" box ticked. Recently on 50MHz to work some FT8 6M DX, I think everybody whose signals I saw/worked must have had their box ticked. Everyone in VK and ZL just stayed on 'their' one frequency.
Probably 25-50% of HF users seem to leave theirs unticked as they end up, however briefly, on the called station's frequency. The rest (50-75%) stay on a specific frequency regardless of who they work so their box is obviously ticked. It's not rocket science and once ticked, it stays that way until deliberately unticked.
One thing that does become obvious though is that operators do not use the waterfall display effectively. I often see a 'continuous wall of signals" in some parts of the audio spectrum, usually mid-band, from HF while others are sparsely used. The WSJT-X software does a magnificent job of handling overlapping 50Hz signal 'bands', and even one completely of the top of the other. On the subject of the waterfall, remember that what you see denoting activity is not what the people at the other end see. There are so many signals being emitted in Europe and the Americas on HF that don't make it this far around the globe but it makes it hard for us to find a frequency that isn't in use over there. A deliberate operating ploy is to jump your transmit frequency around a bit if you cannot 'make or complete the contact' in the hope that somewhere along the line you will land on a 'clear frequency' at their end. Same thing happens at VHF.
You mention 'at least 300 to 2500 Hz' but I often see signals down at 200Hz and below, and up at 3KHz and slightly over. What some operators fail to recall is that the likes of a typical USB (or LSB) filter attenuates everything below 300Hz and above 2400-2500Hz, not to mention audio filtering in the interconnecting audio interface. Modern DSP rigs have other bandpass options but not all are using these rigs, just luckily I am and I use it carefully. I don't transmit with a setting below 400 or above 2200 as a matter of course.
It comes down to : if you see what looks like a spare 50Hz over several 30 second segments, grab it - but be prepared to QSY as needed.
73 Doug
Doug VK4ADC @ QG62LG51
http://www.vk4adc.com
This Forum is only going to be as interesting as the posts it contains.
If you have a comment or question, post it as it may trigger or answer the query in someone else's mind.
http://www.vk4adc.com
This Forum is only going to be as interesting as the posts it contains.
If you have a comment or question, post it as it may trigger or answer the query in someone else's mind.