28-02-2017, 10:00 AM
I know Redcliffe Club should be posting this but...
See also http://www.vklogger.com/forum/viewtopic.php?t=13463, titled "VK4RC 10m Beacon - Now On Air"
and from Ozlogger forum topic http://www.ozlogger.net/forum/viewtopic.php?f=12&t=65, titled "28.2115 MHz HF beacon in SE Q'ld now off-air":
"This beacon has been reprogrammed to 28.265 with callsign VK4RRC and will be installed at Wamuran, SEQ, with the other Redcliffe & Districts Radio Club repeaters. The "box" was donated to RDRC and handed over to Kevin VK4UH on the 26th Feb 2017 and is only awaiting the installation of a suitable 28MHz base antenna on-site before it is likely to be operational.
It is set to do the basic CW ID (VK4RRC) at about 7 watts RF out, then RF power step down from 5 watts to 10mW at 1 second intervals. This timing cycle repeats every 20 seconds and a full length ID (VK4RRC Brisbane QG62JX81) every sixth ID. Good luck hearing the 10mW power level unless you are very close to it !!
The beacon will do an RF power re-calibration at least every hour and that revalidates any account antenna impedance changes, power supply voltage changes or component ageing to maintain correct RF output values. This part of the program cycle is obvious as it has "bursts" of increasing RF signal level as it re-sets to meet the targets (instead of decreasing as the power levels step down in the normal beacon cycle - as above in para 2).
It will also add either a HV or LV to the CW ID to indicate either high or low power supply voltages beyond normal tolerance. The unit will cease to produce normal RF output if the supply voltage drops below 11V or exceeds 15V to ensure that RF emissions & transmitter stability is maintained - a LED on the front panel flashes to indicate this state but only about 10mW(/nothing !) is transmitted.
Hopefully it will provide a useful beacon facility to many - for many years.
73 Doug VK4ADC"
The original details on this hardware are shown at http://www.vklogger.com/forum/viewtopic....83&t=13485, titled "SARS YA10MB Project", however there have been further changes inside the box and most definitely in the software that runs it.
Hopefully we will see this new "box" on air shortly - with it's correct callsign, VK4RRC - and the reports will start to flow in.
See also http://www.vklogger.com/forum/viewtopic.php?t=13463, titled "VK4RC 10m Beacon - Now On Air"
and from Ozlogger forum topic http://www.ozlogger.net/forum/viewtopic.php?f=12&t=65, titled "28.2115 MHz HF beacon in SE Q'ld now off-air":
"This beacon has been reprogrammed to 28.265 with callsign VK4RRC and will be installed at Wamuran, SEQ, with the other Redcliffe & Districts Radio Club repeaters. The "box" was donated to RDRC and handed over to Kevin VK4UH on the 26th Feb 2017 and is only awaiting the installation of a suitable 28MHz base antenna on-site before it is likely to be operational.
It is set to do the basic CW ID (VK4RRC) at about 7 watts RF out, then RF power step down from 5 watts to 10mW at 1 second intervals. This timing cycle repeats every 20 seconds and a full length ID (VK4RRC Brisbane QG62JX81) every sixth ID. Good luck hearing the 10mW power level unless you are very close to it !!
The beacon will do an RF power re-calibration at least every hour and that revalidates any account antenna impedance changes, power supply voltage changes or component ageing to maintain correct RF output values. This part of the program cycle is obvious as it has "bursts" of increasing RF signal level as it re-sets to meet the targets (instead of decreasing as the power levels step down in the normal beacon cycle - as above in para 2).
It will also add either a HV or LV to the CW ID to indicate either high or low power supply voltages beyond normal tolerance. The unit will cease to produce normal RF output if the supply voltage drops below 11V or exceeds 15V to ensure that RF emissions & transmitter stability is maintained - a LED on the front panel flashes to indicate this state but only about 10mW(/nothing !) is transmitted.
Hopefully it will provide a useful beacon facility to many - for many years.
73 Doug VK4ADC"
The original details on this hardware are shown at http://www.vklogger.com/forum/viewtopic....83&t=13485, titled "SARS YA10MB Project", however there have been further changes inside the box and most definitely in the software that runs it.
Hopefully we will see this new "box" on air shortly - with it's correct callsign, VK4RRC - and the reports will start to flow in.
Doug VK4ADC @ QG62LG51
http://www.vk4adc.com
This Forum is only going to be as interesting as the posts it contains.
If you have a comment or question, post it as it may trigger or answer the query in someone else's mind.
http://www.vk4adc.com
This Forum is only going to be as interesting as the posts it contains.
If you have a comment or question, post it as it may trigger or answer the query in someone else's mind.